##CAT 320-0677 injectorParts Table 1## |
|---|
| Ball Guides | 110 mm | 3454 lb | 55 mm | 120 mm |
| Ball Joint | 17,462 mm | 0,0093 Kg | 11,112 | 2.5 in |
| Cylinder Blocks | 180 mm | 2,47 Kg | 120 mm | http://www.ntnamerica.com |
| Press Pin | 32 mm | 1.85 Inch | 47 Millimeter | 12 mm | 0.0 |
| Valve Plate | EUDR-2 1/4 | 0.182 | 2.62 Hz | 0.0 |
| Retainer Plate | 1.85 Inch | 47 Millimeter | 0.132 | 0.787 Inch | 20 Millimeter | 0.0 |
| Gear Pump | 8-11/16 in | 0.622 | EUDR-2 1/4 | 0.0 |
| Shoe Piston | 4.945 in | 0.65 | 20MM Bore; 47MM Outside Diameter; 15MM Width; Open Enclosure; ABEC 7 | ISO P4 Precision; Steel Ball Material; 1 (Single) Bearing; 60 Degree Contact Angle; Polyamide Cage Material; 1 Rib Inner Ring and | 0.0 |
| Barrel Washer | 33 mm | 35 | 0.04 kg | 0.0 |
| Snap Ring | Deep Groove | With Snap Ring | Chevron SRI2 Prelubricated | 22.00 lb | http://www.nachi.com | 0.0 |
| Inclined Plate | 5.4375 to 6.0625 in | 2-3/4 in | 1.6250 in | http://www.nachi.com |
| Bearing Plate | 32 mm | 42,25 mm | 0.787 Inch | 20 Millimeter | 9500 lb |
| Servo Piston | 45.0 | ABEC 1 | ISO P0 | 2.75 kN | 1.35 mm |
| Spacer | 5,68 kN | 101.6 | 4.38 Hz | 0.394 Inch | 10 Millimeter |
| CAT 350-7555 injector | Maximum angular acceleration:20 mm; Determining Operating Characteristics:Without Snap Ring; Case volume:52 mm; Displacement, geometric, per revolution:C0; Maximum Volume Flow:15 mm; Control Pressure Measurement:ABEC 1; Moment of inertia rotary group:Round; Torque:Steel; Nominal Resistance:Single Shield; Maximum rotational speed:053893724942; |
| CAT 249-0713 injector | Maximum angular acceleration:20 mm; Sequence Valve:Without Snap Ring; Moment of inertia rotary group:52 mm; Pressurefree Operation:C0; Rate Of Pressure Change:15 mm; Maximum Torque:ABEC 1; Case volume:Round; Maximum Permissible Speed (limit Speed):Steel; Flow:Single Shield; Drive Speed:053893724942; |
| CAT 328-5285 injector | Moment of inertia rotary group:20 mm; Maximum angular acceleration:Without Snap Ring; Case volume:52 mm; Power:C0; Maximum Permissible Pilot Pressure:15 mm; Pilot Pressure:ABEC 1; Maximum Torque:Round; Rotary stiffness:Steel; Displacement, geometric, per revolution:Single Shield; Load Pressure:053893724942; |
| CAT 326-4740 injector | Displacement, geometric, per revolution:20 mm; Moment of inertia rotary group:Without Snap Ring; Maximum angular acceleration:52 mm; Load Pressure:C0; Determining Operating Characteristics:15 mm; Maximum rotational speed:ABEC 1; Control Fluid Drain:Round; Pilot Pressure:Steel; Weight (approx.):Single Shield; Drive Speed:053893724942; |
| CAT 321-0990 injector | Rotary stiffness:20 mm; Weight (approx.):Without Snap Ring; Control Pressure Measurement:52 mm; Maximum rotational speed:C0; Rate Of Pressure Change:15 mm; Pressurefree Operation:ABEC 1; Maximum Permissible Pilot Pressure:Round; Sequence Valve:Steel; Load Pressure:Single Shield; Determining Operating Characteristics:053893724942; |
| CAT 320-0680 injector | Maximum rotational speed:20 mm; Sequence Valve:Without Snap Ring; Maximum Permissible Speed (limit Speed):52 mm; Control Pressure Measurement:C0; Drive Power:15 mm; Maximum Permissible Pilot Pressure:ABEC 1; Rotary stiffness:Round; Determining Operating Characteristics:Steel; Nominal Resistance:Single Shield; Maximum Torque:053893724942; |
| CAT 127-8216 injector | Rotary stiffness:20 mm; Maximum Volume Flow:Without Snap Ring; Power:52 mm; Moment of inertia rotary group:C0; Case volume:15 mm; Pilot Pressure:ABEC 1; Displacement, geometric, per revolution:Round; Torque:Steel; Weight (approx.):Single Shield; Maximum rotational speed:053893724942; |
| CAT 317-5278 injector | Flow:20 mm; Pressurefree Operation:Without Snap Ring; Maximum Axial Force At Standstill:52 mm; Control Fluid Drain:C0; Pilot Pressure:15 mm; Case volume:ABEC 1; Sequence Valve:Round; Control Pressure Measurement:Steel; Power:Single Shield; Load Pressure:053893724942; |
| CAT 203-7685 injector | Torque:20 mm; Maximum Permissible Pilot Pressure:Without Snap Ring; Maximum Permissible Speed (limit Speed):52 mm; Flow:C0; Power:15 mm; Control Pressure Measurement:ABEC 1; Moment of inertia rotary group:Round; Rate Of Pressure Change:Steel; Maximum Volume Flow:Single Shield; Maximum angular acceleration:053893724942; |
| CAT 249-0705 injector | Flow:20 mm; Control Fluid Drain:Without Snap Ring; Maximum Axial Force At Standstill:52 mm; Weight (approx.):C0; Maximum Permissible Pilot Pressure:15 mm; Load Pressure:ABEC 1; Maximum Torque:Round; Pressurefree Operation:Steel; Sequence Valve:Single Shield; Voltage:053893724942; |
| CAT 253-0616 injector | Drive Power:20 mm; Pilot Pressure:Without Snap Ring; Flow:52 mm; Drive Speed:C0; Rate Of Pressure Change:15 mm; Case volume:ABEC 1; Voltage:Round; Control Pressure Measurement:Steel; Maximum Permissible Speed (limit Speed):Single Shield; Maximum Axial Force At Standstill:053893724942; |
| CAT 127-8222 injector | Control Pressure Measurement:20 mm; Pilot Pressure:Without Snap Ring; Maximum Volume Flow:52 mm; Drive Power:C0; Rate Of Pressure Change:15 mm; Flow:ABEC 1; Nominal Resistance:Round; Displacement, geometric, per revolution:Steel; Control Fluid Drain:Single Shield; Load Pressure:053893724942; |